Universal Testing Machines
Available Equipment
Features:

- Digital display of Length and Load.
- Tare set facility for load indicator to set off dead weights of clamps, springs, etc., and to read actual load directly.
- Length reset facility for length indicator at any position of moving platen to indicate actual deflection.
- Fully automatic test with single button test start.
- Easy to program controller.
- This equipment is extremely versatile for conducting a variety of tests, on different materials as per national and international standards.
Available in two models:
- With Fixed Testing Speed (Model UTM and UTM-P)
- With Variable Testing Speed (Model UTM-V and UTM-P(V))
Among the many tests that can be conducted on the machine are:
- Actuating Force for Snap Action Switch
- Removal Force for Connector PIns in Plugs
- Tensile Strength of Crumple Terminals
- Firmness of Polyurethane Foam
- Tensile Strength of Rubber - Fiber and Filaments
- Crush Strength of Medical Tablets
- Peel Strength of Adhesives
- Flexural Test for Laminates, PCBs, Plastics,etc.
- Fruit Firmness Test
- Sealing Strength of Pouches and Bags
- Test for Springs, agnets,etc.
Additional Features of Micro Processor-based Equipment (Model UTM-P and Model UTM-P(V):
- Printer Port to Print Load and Length/Deflection Graph of Test Data (80 column dot matrix Printer to be provided by user).
- RS232 Port for data transfer to PC/Data Transfer Unit with dedicated Software for Test Analysis (Optional at extra cost).
- Hardware Requirement: PC with CD-ROM drive, Serial Port, minimum 64 MB RAM, Hard Disk with Windows 98 preloaded.
Parameter | Specifications for both Models | ||
---|---|---|---|
Loading Speed (to be specified with the order) | Model UTM / UTM-P | Any one specific speed between 12 ± 3 mm/min to 100 ± 3mm/min | |
Model UTM-V / UTM-P(V) | 1-100 mm/min or 4 Preset speeds (to be specified) or Higher Loading Speed** | ||
Load Cell Capacity (KgF) To be specified with the order | 20, 50, 100, 200, 500, 1000 (Loading Capacity will be approximately 90% of Load Cell Capacity.) This machine can be configured to operate with up to three Load Cells of different capacities (Optional at extra cost) | ||
Load Indicator Resolution | 0.1% of Loading capacity | ||
Load Indicator Accuracy | ± 0.4% of Loading Capacity | ||
Load Units (User Selectable) | KgF, Newton, Pound | ||
Admit between Platens | Minimum 100 mm Maximum 500 mm | ||
Power Requirement | 3 Phase, 415 VAC, 1.5 HP with independent and effective neutral and earthing | ||
Length Indicator Resolution | 0.1 mm | ||
Length Indicator Accuracy | ± 0.2 mm | ||
Dimensions of the Standard Machine with Control Panel (W x D x H) mm | 1200 x 1100 x 1700 (Approx.) | ||
Machine Weight of the Standard Machine | 800 kgs (Approx.) |
Features:

- Flexible simple-to-use control console, which can be positioned at convenient angle.
- Motorized machine, with sensitive electronic Load and Length Indicators.
- Length reset facility for length indicator at any position of moving platen to indicate actual deflection.
- Tare Set facility to off-set dead weights of samples, clamps, adapters, mounts, etc.
- Over-load indication by audio annunciation.
- This equipment is extremely versatile for conducting Tensile Strength Test of paper, paperboard, etc. It can also be useful for testing compression and tension forces.
Following tests also can be conducted on this equipment:
- Testing of tension and compression springs.
- Insertion and pull-out force checking for connectors, plug-in PCBs, etc.
- Tensile testing of crimped terminals.
- Operational/Actuating force checking of electrical switches, buttons, aerosol cans, etc.
- Testing of rubbers, plastics, fibers, filaments, textiles, papers, boards, aluminum and other non-ferrous foils, etc.
- Measuring firmness of foams and sponges of polyurethane, latex, coir, polystyrene, etc.
- Testing crush strength of medicinal pills, tablets, capsules, etc.
- Flexural & Shear checking of pipes, tubes, PCBs, etc.
- Calibrate magnets.
- Peel & Adhesion Strength of stickers, labels, BOPP tapes, laminates, Adhesives, surgical tapes, etc.
- Crush/Compression strength checking for packing materials viz, paper, boards, bottles, cartons, etc.
Options:
- Increased admit between Platens.
- Plotter or digital data logger.
- Twin Load cell arrangement for sensing forces in 2 different ranges accurately.
- Range Selector for single load cell to sense forces in low range.
- Step less Variable Loading Speed on request.
- Optional Grips and Fixtures-Self-tightening Tensile Grip, Puncture Test Fixture, TW Wrapped Wire Connector Grip, Spool Grip, 90 degrees Peel Test Fixture, Flat Tensile Grip, Ring & Flat Crush Fixtures.
- Peak-hold to Instant Reading change over by simple switch operation.
Suitable for Testing as per following Standards
IS : | 1924 (Part II) 1995 |
TAPPI : | T 494 om-01 |
ASTM : | D 828-93s |
Technical Specifications
Max. Admit between Platens | 300 mm |
Minimum Admit | 50mm |
Loading Capacity | 250 kgf |
Load Sensing Capacity | 5 / 10 / 50 / 100 / 200 kg |
Load Indicator Resolution | 0.2% Full Scale |
Load Indicator Sensitivity | 0.4% FS |
Length Indicator Resolution | 0.1 mm |
Length Indicator Accuracy | 0.2 mm |
Loading Speed | 12.5 mm/min. or as specified up to max. 50 mm/min (provided Load Cell capacity is more than 25 kgf) |
Electric Supply Requirement | 1 Phase 220 V-AC 50 Htz with positive Neutral Earthing |
Following Versions Are Available
Features:

- Microprocessor based provides immense flexibility. Adjustable stroke.
- Programmable set points of load and length.
- Can test multiple points of compression in a single stroke.
- Displays Accept / Reject status immediately after test.
- Results can be printed directly from printer port of microprocessor.
- RS232 port of transfers data to PC.
- PC software for data analysis.
Also available
Features and Technical Specifications of this product is available on request.Spring Rate Testers
Spring Endurance Testers
Spring Sorters
Related Product Images (click to enlarge)